11/13/2022 0 Comments Power mac g5 case mods
The Thumb screw do hang over the Mobo tray a bit however thats not an issue as my parent PC uses and mATX board. With lower bars into place (case is upside down) I had allowed 2mm of play with the vertical bars just in case, turns out that with a bit of filing ect I get about 1mm of extra space so i just some rubber to fill the gap and damped some vibrations (I was hoping for Rubber on both ends but the fit was too tight) Screw it altogether and do a test fitting. the countersunk bars are going to connect to the case so they need to be flush. I drilled a few screw holes in he 170mm bars and Tapped both end of the 87mm bars. Unlike most G5 conversions I don't really want to use the top shelf and getting it out is a pain with the mobo installed (that and I might have slightly murdered the top shelf while I was in a rage trying to get it out before I rage quite)ĤX 170X3X20mm and 4X 87X10X20mm (stupid 20mm thick stuff is a pain to cut with my crappy rig saw). I did manage to snap a screw off in one of the SSDs holes (stupid Alu screws are very easy to break if you cross thread them) I glue them to he case with the HDDs in place to make sure the spacing is correct. To handle the HDDs I will be using a few bits of Alu L bar.ĭrill some holes for the SSD and HDD to screw into. JB Weld to the rescue (well a rip off) from Supercheap. Now to fit the PSU and HDDs into the case. The magnets fit perfectly in the grove behind the crossbeam where the old latching mechanism went and old in place without any glue (they are bastards to get back out) Luckily the cross beam and metal frame on the side panel are steel so installing and holding the Panel in place was very easy. Yes many Macs died in the making of this case (About 10 Macbooks I believe) These magnets are from the screen of Old White Macbooks. Leaving the latch in place means that you have to cut around it when installing the ATX backplane which means more work and the Job looks less seamless, So off to my Magnet stash I go to find some suitable for this Job. #Power mac g5 case mods mods#Use magnets on all of the Mods cos i'm crazy like that). Unlike most G5 conversions I don't really want to use the built in latch for holding on the side panel so I have come up with an alternative solution using magnets (PS yes I #Power mac g5 case mods driver#i also have to literally rip the Heat sink out because i did not have a really really long torx screw driver that was really thing (2 screw under the HS needed a 20cm long Torx Screw driver that is less than 5mm wide for the full length). #Power mac g5 case mods how to#It took quiet a while to undo all of the torx screws holding the hardware in and figuring out how to remove the top shelf took a while (about 8 months cos I Rage quit for a while and then about 3 weeks before my parents were due to leave I spent 5 minutes on Google and figured it out LOL). The case has been cleansed of the Old Maccy Badness. #Power mac g5 case mods mod#I should ahve taken more Photos before i started to Mod the case but its too late now. #Power mac g5 case mods for free#I managed to score this case for free from Work however it is a bit beat up so it will never look perfect, Free is free so I cant complain. My parents are too IT inept to change from PC to Mac. Having a Mac will make you fit in in Melbourne Below are my assumptions that lead to this Mod. Let me know, pls.Shortly my parents are moving to Melbourne and given my assumptions about Melbourne I have decided to convert an old Power Mac G5 to an ATX case. If you had that saved by any chance, that'd be cool. Lime: That link you posted in your thread on the other site for rewiring the power swtich is dead. Those are some preliminary thoughts without having actually seen the inners of a G5 enclosure. The power cord can reach inside the case otherwise I'd have to cut things since the power outlet hole is right in the middle. This probably means that I'd have to leave the Mac I/O ports empty and out of use but that's fine (fill them with gray putty or something. My plan is a little ghetto but this is what I've thought up: Instead of cutting up the back or modding it in any way, I'd simply use adapters or extensions to access the I/O board connectors on the motherboard and place those in the expansion slots using slot plates I can get from the store (hopefully). The only real problem is that I haven't yet seen the inside of a G5 so I wouldn't know what to expect (other than from photos like yours). I'd rather take the opposite approach and let the case shape the way I place the parts inside not shape the case myself to let the parts fit. So given my littlle experience I'm trying to avoid "modding", so to speak, the case at all costs. I've never modded a case before in my life and so if I pull through with this it'd be a first. Well, one thing's for sure I'm not a modder.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |